A crane lifts the 26000 kg steel hull of a ship out of the water. Determine the tension in the crane's cable when the hull is submerged in the water. Determine the tension when the hull is completely out of the water.

A crane lifts the 26000 kg steel hull of a ship out of the water. Determine the tension in the crane's cable when the hull is submerged in the water. Determine the tension when the hull is completely out of the water.

Name: A crane lifts the 26000 kg steel hull of a ship out of the water. Dete
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: A crane lifts the 26000 kg steel hull of a ship out of the water. Determine the tension in the crane's cable when the hull is submerged in the water. Determine the tension when the hull is completely out of the water.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter6: Beams And Cables

Section: Chapter Questions

Problem 6.71P: The tensions in the cable at points O and B are TO=1200N and TB=1800N. Determine the weight W of the...

See similar textbooks

Similar questions

The weight of the cylindrical tank is negligible in comparison to the weight of water it contains (water weighs 62.4lb/ft3). The coefficient of static friction between the tank and the horizontal surface is s. (a) Assuming a full tank, find the smallest force P required to tip the tank, and the smallest s that would allow tipping to take place. (b) If the force P = 200 lb initiates tipping, determine the depth of water in the tank.
The tensions in the cable at points O and B are TO=1200N and TB=1800N. Determine the weight W of the cable.
Each of the three gates has a constant width 1: (perpendicular to the paper). Calculate the force P required to maintain each gate in the position shown. Express your answers in terms of b, c, h, and (the weight density of the fluid).
A crane is used to lower weights into the sea (density = 1,025 kg/m3) for an underwater construction project. Determine the tension in the rope of the crane due to a rectangular 0.4m x 0.4m x 3m concrete block (density = 2,300 kg/m3) when it is completely immersed in water.
Cords are looped around a small spacer separating two cylinder each weighing 400kn and pass over a frictionless pulleys to weights of 200KN and 400kn. Determine the angle and the pressure N between the cylinder and smooth horizontal surface
A mass of 10 kg and 5 kg mass are tied to a light string and hung over a frictionless pulley. Determine the accelaration and tension on the sting. Assume a weightless and a frictionless pulley.
Two men exert forces F and P on the ropes. If P = 48 Ib, what is the required force F to maintain equilibrium? Supply the answer in pounds. 6 ft 12 ft
Q3) The gusset plate is subjected to the forces of four members. The forces are concurrent at point 0. If the force in member C is (F =12 kN) determine the force (T) in member B and its proper orientation 0 for equilibrium. SKN 5kN
4. A crane is used to lower weights into a lake for an underwater construction project. Determine the tension in the rope of the crane due to a 3-ft diameter spherical steel block (density 5 494 lbm/ft)when it is (a) suspended in the air and (b) completely immersed in water. Fa
Find the weight of WB necessary to hold WC in the position shown, given:WC = 250 N, θ = 20 °, Φ = 10 °, x,y,h = 4,3,5, respectively
A crate with dimensions l = 0.50 m and h = 0.75 m rests on a plane that is inclined by θ = 30◦ from thehorizontal. The crate is in equilibrium, but if the crate were too tall, it will fall over down the slope.Find the effective point of application of the normal force on the crate, i.e., where is the normal force actingon the crate, keeping the crate in equilibrium? Hint: choose the crate’s center of mass as the axis of rotation.
The blade of the bulldozer shown below is rigidly attached to a linkage consisting of the arm AB, which is controlled by the hydraulic cylinder BC. There is an identical linkage on the other side of the bulldozer. Applied loads shown are for both linkages and F = 581 kN. Determine the pressure in hydraulic cylinder BC in Pa if the cylinder has a diameter of 80 mm.